|
T-SHAPED
STRUCTURAL RAIL
A level rail is important. We place leveling screws on both
sides of the rail. It is then precisely leveled and under filled
with grout to form a concrete-like strong base. Each track joins
together perfectly, like a model train. The rails are end
drilled to accept a 3/8" steel pin. The result: Systems that
move smoothly and silently. Our standard rail is 1 1/2" high and
2 1/2" wide.
DECK AND RAMP
A Jeter deck feels solid, like the floor underneath it. Decks
are made of tongue and groove, 3/4" plywood. Leveling screws are
placed 16" apart, which makes our decks adjustable to most any
floor condition. All edges are finished, and the deck arrives
ready to receive the covering of your choice.
 |
|
CENTER DRIVE, CROSS OVER CHAIN
We also use a cross over chain to connect the two drive shafts.
This chain is a much heavier, Harley Davidson size chain. It
transfers power to the drive line, which moves all wheels on one
side of the carriage. By driving the system at the carriage
center, we achieve perfect, uniform back and forth motion. All
sprockets are welded securely to the 1" solid steel shafts. The
shafts are supported by heavy-duty pillow block bearings, rated
at 1,800 lbs each. We have installed over 10,000 systems. Our
mobile systems are designed for long-lasting reliability.
WELDED CARRIAGE FRAME
Our strong, ladder-shaped carriage frame is designed to support
a maximum weight load of 1,100 lbs per carriage foot. Our
systems roll easily due to the precise squareness of the
carriage. The frame parts are clamped to a unique fixture, then
welded to a tolerance within thousandths of an inch. Each
carriage is designed from 12-gauge, .110" thick 1008/1010 AISI
steel.
RECESSED LIP SAFELY SECURES CABINETS
Jeter carriages provide recessed lips to contain shelving within
the structure of the carriage. This secures the shelving, so
that it cannot shift during carriage movement. Other
manufacturers offer carriages where shelving "just sits" on top.
With Jeter, you’ll receive a system that offers superior
quality, safety and reliability.
SERVICE-FREE CHAIN DRIVE SYSTEM
All systems come with a unique, patented automatic chain
tensioner. It adjusts and compensates for chain stretch. This
chain tensioner is a key component to ensure your Jeter system
will remain service-free –– for the life of the system.
CARRIAGES ROLL EFFORTLESSLY
Each Jeter mobile system is carefully designed. We analyze the
weight that will be placed on the carriages and assign the
proper gear ratio. Our systems roll on 5" drive wheels, and
guidance is provided by flanged wheels at both ends of the
system. All center position wheels are flat. Our systems move
thousands of pounds with truly finger-tip effort. An average
system moves 6,000 lbs with 1 lb of effort at the handle –– it’s
easy.
VARIETY OF END PANEL COLORS
End panels are offered in a variety of colors. The quality
appearance will compliment your office decor. And, the end
panels close leaving a 3/4" gap so that fingers cannot get
injured. We design our systems making safety first, always.
SAFETY BRAKES Our reliable safety brake is activated by a knob
above the handle. Safety brakes are installed on carriages 12"
or longer and on all x-ray systems. It is optional on all other
systems.
STATIONARY CARRIAGES BOLTED TO RAIL
Stationary units are an integral part of each Jeter mobile
system. When a carriage abruptly hits a stationary unit,
thousands of pounds of energy must be absorbed. Our stationary
units are firmly bolted to the rail, which is secured to the
floor. This guarantees the perfect positioning of rails at the
time of installation.
QUALITY
INSTALLATIONS ELIMINATE SERVICE CALLS
All systems are thoroughly reviewed at our factory prior to
shipment. Each piece is marked for correct placement during
installation. All hardware for assembly is provided, including
carpet trim to have the system look perfect. And, installations
are completed by experienced, factory-trained service
technicians. |
